If you operate a business or manage a property in Toronto, you may be wondering whether the city's water supply is considered hard water. Hard water contains high levels of dissolved minerals, such as calcium and magnesium. While hard water is not harmful to drink, it can cause problems for a building's plumbing, appliances, and fixtures. In this article, we take a closer look at Toronto's water supply and answer the question: does Toronto have hard water?
Toronto's Water Supply
Toronto's municipal water supply comes from Lake Ontario and is treated at four water treatment plants before being distributed throughout the city. The treatment process includes disinfection, filtration, and fluoridation to ensure the water is safe to drink and meets the guidelines set by Health Canada.
Hard Water in Toronto
According to the City of Toronto, the city's water supply has a hardness level of 124 milligrams per litre (mg/L), or 7.3 grains per gallon (GPG). This means Toronto's water is considered moderately hard. While it may not cause major problems for every building, it can still lead to scale buildup in pipes, faucets, and equipment over time.
Effects of Hard Water
The effects of hard water vary depending on the level of hardness and the specific minerals present. Some common effects include:
- Scale buildup in pipes and appliances
- Stains on fixtures and glassware
- Reduced efficiency of water heaters and equipment
- Higher energy and maintenance costs over time
Solutions for Hard Water
If your facility is experiencing problems with hard water, several solutions are available:
- Water softeners remove the minerals that cause hardness and prevent scale buildup in pipes and appliances.
- Reverse osmosis systems use a membrane to remove impurities, including minerals, from the water.
- Whole-building water descalers combat hard water issues, preserving plumbing, improving energy efficiency, and extending equipment life.
While Toronto's water supply is only moderately hard, it can still cause problems for a building's plumbing, appliances, and fixtures. If your facility is experiencing hard water issues, MT Treatment can help you choose the right commercial solution and keep your water systems running reliably.
How hard is 124 mg/L on the hardness scale?
Water hardness is usually reported in milligrams per litre (mg/L) of calcium carbonate or in grains per gallon (GPG), where 1 GPG equals about 17.1 mg/L. The general scale used across the industry runs from soft to very hard:
- Soft: 0–60 mg/L (0–3.5 GPG)
- Moderately hard: 61–120 mg/L (3.5–7 GPG)
- Hard: 121–180 mg/L (7–10.5 GPG)
- Very hard: 180+ mg/L (10.5+ GPG)
At roughly 124 mg/L (7.3 GPG), Toronto sits right at the line between moderately hard and hard. That is mild compared with well-fed systems in parts of York Region or Barrie, but it is still high enough to form scale steadily on any surface that heats or holds the water — which is exactly where commercial equipment lives.
Why moderately hard water still matters for commercial buildings
In a home, 124 mg/L is a nuisance — spotty glassware, a little scale in the kettle. In a commercial building the same water runs continuously through equipment that is expensive to repair and disruptive to shut down. Scale is an insulator: even a thin layer on a boiler heat exchanger or a water-heater element forces it to burn more energy to deliver the same hot water, and a 1–2 mm scale layer can raise heating energy use by several percent. Over a year of continuous operation, that shows up as higher gas bills, shortened equipment life, more frequent service calls, and — in kitchens and laundries — visible spotting and premature failure of dish machines, combi ovens, ice makers, and steamers.
The minerals do not disappear when water is heated or evaporated; they concentrate. That is why the hottest, highest-use points in a building — boilers, cooling towers, dishwashers, and steam equipment — scale up first and worst, even on a supply the city classifies as only moderately hard.
How to confirm the hardness at your building
The City of Toronto's published figure is a system average, but the water at your tap depends on your location in the distribution network, your building's plumbing, and whether any existing treatment is in place. The only way to size a softener or filtration system correctly is to test the water your building actually receives. We bring test equipment on site, measure hardness along with iron, chlorine, and other relevant parameters, and use those numbers to recommend a system sized to your real flow and demand rather than a regional average.
Contact us